СИСТЕМА ECD > РЕГИСТРАЦИЯ |
1. INPUT INJECTOR COMPENSATION CODE(S) INTO ECM |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Turn the tester on.
Enter the menu options in this order: Powertrain / Engine and ECT / Utility / Injector Compensation.
Press "Next".
Press "Next" again to proceed.
Select "Set Compensation Code".
Press "Next".
Select the number of the cylinder corresponding to the injector compensation code that you want to read.
Press "Next".
Register the compensation code.
Press "Input".
Manually input the cylinder's compensation code using the keyboard on the tester screen. The code is a 30-digit, alphanumeric value imprinted on the injector's head portion.
Confirm that the compensation code is correct for the selected cylinder, and then press "OK".
Check that the compensation code displayed on the screen is correct, by comparing it with the 30-digit alphanumeric value on the head portion of the injector.
Press "Next" to set the compensation code to the ECM.
To continue with compensation code registrations for other cylinders, press "Next". To finish the registration, press "Cancel".
Turn the ignition switch off and then turn the tester off.
Wait for at least 30 seconds.
Turn the ignition switch on (IG) and then turn the tester on.
Clear DTC P1601 stored in the ECM using the tester (See page Нажмите здесь).
2. INPUT ALL INJECTOR COMPENSATION CODES AND TRANSFER CATALYST RECORD OF DPNR THERMAL DETERIORATION |
Read the catalyst record of DPNR thermal deterioration.
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Turn the tester on.
Enter the menu options in this order: Powertrain / Engine and ECT / Utility / Catalyst Record Transferring.
Press "Next".
Press "Next" again to proceed.
Press "Next" again to proceed.
Select "Step 1 Read catalyst record".
Press "Next".
Confirm the catalyst record and press "Next".
If the catalyst record has already been stored in the tester, the message in the illustration will appear. Press "Replace".
Press "Exit".
Read the injector compensation codes.
Enter the menu options in this order: Powertrain / Engine / Utility / Injector Compensation.
Press "Next".
Press "Next" again to proceed.
Select "Read Compensation Code".
Press "Next".
Select the number of the cylinder corresponding to the injector compensation code that you want to read.
Press "Next".
Check that the injector compensation code (30-digit alphanumeric value) is displayed on the tester screen.
Press "Save".
Check that the compensation code displayed on the tester screen is correct.
Press "Save" or "Replace" to save the injector compensation code.
To read and save injector compensation codes for other cylinders, press "Next" to continue. To finish this operation, press "Cancel".
Turn the ignition switch off.
Turn the tester off.
Replace the ECM (See page Нажмите здесь).
Set the catalyst record of DPNR thermal deterioration.
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Turn the tester on.
Enter the menu options in this order: Powertrain / Engine and ECT / Utility / Catalyst Record Transferring.
Press "Next".
Press "Next" again to proceed.
Press "Next" again to proceed.
Select "Step 3 Set catalyst record".
Confirm the catalyst record and press "Next".
Press "Exit".
Set the injector compensation code.
Enter the menu options in this order: Powertrain / Engine and ECT / Utility / Injector Compensation.
Press "Next".
Press "Next" again to proceed.
Select "Set Compensation Code".
Press "Next".
Select the number of the cylinder corresponding to the injector compensation code that you want to read.
Press "Next".
Check that the compensation code displayed on the screen is correct, by comparing it with the 30-digit alphanumeric value on the head portion of the injector.
Press "Next" to set the compensation code to the ECM.
To continue with compensation code registrations for other cylinders, press "Next". To finish the registration, press "Cancel".
Clear DTC P1601 stored in the ECM using the tester.
Turn the ignition switch off and then turn the tester off.
Wait for at least 30 seconds.
Turn the ignition switch on (IG) and then turn the tester on.
Clear DTC P1601 (See page Нажмите здесь).