ТРОС МЕХАНИЗМА ПЕРЕКЛЮЧЕНИЯ ПЕРЕДАЧ (для моделей с кузовом типа "седан") > УСТАНОВКА |
1. INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY |
Install the transmission control cable assembly with the 2 nuts and bolt.
Install the transmission control cable to the control cable bracket with 2 new clips.
Install the transmission control cable to the transaxle with the 2 clips.
Rotate the transmission control cable nut counterclockwise approximately 180° and, while holding the nut in that position, press in the stopper until it makes 2 "click" sounds.
Install the cable outer of the transmission control cable to the shift lever retainer, check that the position of the spring is the same as A shown in the illustration, and press in the stopper.
Install the clip to the shift lever.
Install the control shift cable to the shift lever assembly.
Install the control select cable to the shift lever assembly.
2. ADJUST TRANSMISSION CONTROL CABLE ASSEMBLY |
Install the transmission control cable assembly on the transmission.
Using a screwdriver, pull the lock piece out from the adjuster case.
Pressing the shift and select lever shaft (*1) and pin (*2), push in pin (*3) and check that the shift and select lever shaft is secured at the 1st-2nd gear selected position (the shaft comes to a stop at the position 8 mm (0.31 in.) below the N position).
Remove the stopper pin, release the lock, and reinsert the stopper pin.
Turn the shift lever in the reverse direction without pulling up the slider shaft.
Install the transmission control shift cable to the shift lever assembly.
Install the control select cable to the shift lever assembly.
Install the clip to the shift lever.
Press in and lock the lock piece to the adjuster case.
Release the pin that fixes the transmission outer lever.
Pull the pin toward the front left side of the vehicle.
3. INSTALL REAR CONSOLE BOX ASSEMBLY |
Вверните 2 винта.
Установите вещевой ящик в облицовке туннеля пола и закрепите его 4 болтами.
4. INSTALL CONSOLE BOX CARPET |
Установите коврик вещевого ящика в облицовке туннеля пола.
5. INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY |
Установите верхнюю панель консоли и закрепите ее 8 фиксаторами.
6. INSTALL FRONT NO. 2 CONSOLE BOX INSERT |
Введите в зацепление направляющую.
Введите в зацепление 3 захвата и установите переднюю вставку вещевого ящика в облицовке туннеля пола № 2.
7. INSTALL FRONT NO. 1 CONSOLE BOX INSERT |
Введите в зацепление направляющую.
Введите в зацепление 3 захвата и установите переднюю вставку вещевого ящика в облицовке туннеля пола № 1.
8. INSTALL INSTRUMENT PANEL BOX ASSEMBLY |
Введите в зацепление 2 захвата.
Установите ящик панели приборов и закрепите ее 2 винтами <B>.
9. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY |
Введите в зацепление 2 захвата и 2 фиксатора и установите центральную облицовку панели управления.
10. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY |
Поверните рукоятку рычага переключения передач по часовой стрелке и закрепите ее.
11. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL RH |
Введите в зацепление 2 захвата и 2 фиксатора и установите правую отделочную накладку панели приборов.
12. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL LH |
Введите в зацепление 3 захвата и фиксатор и установите левую нижнюю отделочную накладку панели приборов.
13. INSTALL NO. 1 FRONT FLOOR HEAT INSULATOR |
Install the No. 1 front floor heat insulator with the 3 nuts.
14. INSTALL FRONT EXHAUST PIPE ASSEMBLY (for 1AD-FTV) |
15. INSTALL AIR CLEANER CASE SUB-ASSEMBLY (for 1AD-FTV) |
Install the 3 bolts and air cleaner case.
16. INSTALL AIR CLEANER CAP SUB-ASSEMBLY (for 1AD-FTV) |
Install the air cleaner filter element.
Install the air cleaner cap sub-assembly, and connect the 2 clamps and band.
Connect the No. 2 ventilation hose.
Connect the mass air flow meter connector.
17. INSTALL BATTERY TRAY |
18. INSTALL BATTERY |
19. INSTALL BATTERY CLAMP SUB-ASSEMBLY (for 1AD-FTV) |
Install the battery clamp.
20. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
21. INSTALL UPPER RADIATOR AIR DEFLECTOR (for 1AD-FTV) |
Install the 6 clips and upper radiator air deflector.
22. INSPECT FOR EXHAUST GAS LEAK (for 1AD-FTV) |
Check that there are no exhaust gas leaks from the points (jointed parts of the exhaust pipes and installed parts of each sensor) shown in the illustration.