ТРОС МЕХАНИЗМА ПЕРЕКЛЮЧЕНИЯ ПЕРЕДАЧ (для моделей производства ТМС с кузовом типа "хэтчбэк") > УСТАНОВКА |
1. INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY |
Install the transmission control cable assembly with the 2 nuts and bolt.
Install the transmission control cable assembly to the control cable bracket with 2 new clips.
Install the transmission control cable assembly to the transaxle with the 2 clips.
Connect the control cable assembly to the shift lever assembly.
Install the control select cable to the shift lever assembly.
Install the control shift cable to the shift lever assembly.
2. ADJUST TRANSMISSION CONTROL SELECT CABLE |
Install the transmission control cable assembly to the manual transaxle.
Release the lock of the cable length adjustment structure of the select cable.
Slide the preventive part (slider) of lock release.
Release the lock of the cable length adjustment structure to push out the lock piece from the case.
Install the transmission control cable assembly to the shift lever assembly.
Pressing the shift and select lever shaft (*1) and pin (*2), push in pin (*3) and check that the shift and select lever shaft is secured at the 1st-2nd gear selected position (the shaft comes to a stop at the position 8 mm (0.31 in.) below the N position).
Remove the stopper pin, release the lock, and reinsert the stopper pin.
Turn the shift lever in the reverse direction without pulling up the slider shaft.
Lock the cable length adjustment structure of the select cable.
Release the pin that fixes the transmission outer lever.
Pull the pin toward the front left side of the vehicle.
3. INSTALL LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL |
Введите в зацепление 2 захвата и направляющую.
Введите в зацепление 4 захвата и 2 направляющие.
Установите нижнюю отделочную накладку панели приборов № 1 и закрепите ее 2 винтами <E> или <F>.
4. INSTALL LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL |
Введите в зацепление 2 захвата и направляющую.
Установите нижнюю отделочную накладку панели приборов № 2 и закрепите ее 2 винтами <E> или <F>.
5. INSTALL INSTRUMENT PANEL UNDER TRAY |
Установите нижний лоток панели приборов и закрепите его 4 захватами.
6. INSTALL FRONT NO. 1 CONSOLE BOX INSERT |
Введите в зацепление направляющую.
Введите в зацепление 3 захвата и установите переднюю вставку вещевого ящика в облицовке туннеля пола № 1.
7. INSTALL FRONT NO. 2 CONSOLE BOX INSERT |
Введите в зацепление направляющую.
Введите в зацепление 3 захвата и установите переднюю вставку вещевого ящика в облицовке туннеля пола № 2.
8. INSTALL REAR CONSOLE BOX ASSEMBLY (w/o Console Box Lid) |
Введите в зацепление 4 захвата.
Установите вещевой ящик в облицовке туннеля пола и закрепите его 4 болтами и 2 винтами.
9. INSTALL REAR CONSOLE BOX ASSEMBLY (w/ Console Box Lid) |
Введите в зацепление 4 захвата.
Установите вещевой ящик в облицовке туннеля пола и закрепите его 4 болтами и 2 винтами.
10. INSTALL CONSOLE BOX CARPET (w/o Console Box Lid) |
Установите коврик вещевого ящика в облицовке туннеля пола.
11. INSTALL CONSOLE BOX CARPET (w/ Console Box Lid) |
Установите коврик вещевого ящика в облицовке туннеля пола.
12. INSTALL LOWER CENTER INSTRUMENT PANEL FINISH PANEL |
Введите в зацепление 4 захвата и 6 фиксаторов и установите центральную нижнюю облицовочную накладку панели приборов.
13. INSTALL UPPER CONSOLE PANEL |
Введите в зацепление 7 захватов и установите верхнюю облицовку панели пола.
14. INSTALL REAR CONSOLE BOX COVER |
Подсоедините разъем.
Установите крышку вещевого ящика в облицовке туннеля пола и закрепите ее 4 фиксаторами.
15. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY |
Поверните рукоятку рычага переключения передач по часовой стрелке и закрепите ее.
16. INSTALL INSTRUMENT PANEL FINISH PANEL END LH |
Введите в зацепление 4 фиксатора и установите левую отделочную накладку панели приборов.
17. INSTALL INSTRUMENT PANEL FINISH PANEL END RH |
Введите в зацепление 4 фиксатора и установите правую отделочную накладку панели приборов.
18. INSTALL NO. 1 FRONT FLOOR HEAT INSULATOR |
Install the No. 1 front floor heat insulator with the 3 nuts.
19. INSTALL FRONT EXHAUST PIPE ASSEMBLY (for 1AD-FTV) |
20. INSTALL AIR CLEANER CASE SUB-ASSEMBLY (for 1AD-FTV) |
Install the 3 bolts and air cleaner case.
21. INSTALL AIR CLEANER CAP SUB-ASSEMBLY (for 1AD-FTV) |
Install the air cleaner filter element.
Install the air cleaner cap sub-assembly, and connect the 2 clamps and band.
Connect the No. 2 ventilation hose.
Connect the mass air flow meter connector.
22. INSTALL BATTERY TRAY |
23. INSTALL BATTERY |
24. INSTALL BATTERY CLAMP SUB-ASSEMBLY (for 1AD-FTV) |
Install the battery clamp.
25. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
26. INSTALL UPPER RADIATOR AIR DEFLECTOR (for 1AD-FTV) |
Install the 6 clips and upper radiator air deflector.
27. INSPECT FOR EXHAUST GAS LEAK (for 1AD-FTV) |
Check that there are no exhaust gas leaks from the points (jointed parts of the exhaust pipes and installed parts of each sensor) shown in the illustration.