РЫЧАГ ПЕРЕКЛЮЧЕНИЯ ПЕРЕДАЧ (для моделей с кузовом типа "хэтчбэк") > УСТАНОВКА |
1. INSTALL SHIFT LEVER ASSEMBLY |
Install the shift lever assembly with the 4 nuts.
Install the 2 wire harness clamps to the shift lever assembly.
Connect the 2 connectors to the shift lever assembly.
2. INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY |
Turn the lock nut of the transmission control cable counterclockwise. While holding the lock nut, push in the lock.
Connect the outer part of the transmission control cable to the shift lever retainer.
Slide the slider of the transmission control cable in the direction indicated by the arrow and pull the lock piece outward.
Install the transmission control cable end to the shift lever assembly.
Push the lock piece into the adjuster case.
3. INSTALL LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL |
Введите в зацепление 2 захвата и направляющую.
Установите нижнюю отделочную накладку панели приборов № 2 и закрепите ее 2 винтами <E> или <F>.
4. INSTALL LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL |
Введите в зацепление 2 захвата и направляющую.
Введите в зацепление 4 захвата и 2 направляющие.
Установите нижнюю отделочную накладку панели приборов № 1 и закрепите ее 2 винтами <E> или <F>.
5. INSTALL INSTRUMENT PANEL UNDER TRAY |
Установите нижний лоток панели приборов и закрепите его 4 захватами.
6. INSTALL FRONT NO. 1 CONSOLE BOX INSERT |
Введите в зацепление направляющую.
Введите в зацепление 3 захвата и установите переднюю вставку вещевого ящика в облицовке туннеля пола № 1.
7. INSTALL FRONT NO. 2 CONSOLE BOX INSERT |
Введите в зацепление направляющую.
Введите в зацепление 3 захвата и установите переднюю вставку вещевого ящика в облицовке туннеля пола № 2.
8. INSTALL REAR CONSOLE BOX ASSEMBLY (w/o Console Box Lid) |
Введите в зацепление 4 захвата.
Установите вещевой ящик в облицовке туннеля пола и закрепите его 4 болтами и 2 винтами.
9. INSTALL REAR CONSOLE BOX ASSEMBLY (w/ Console Box Lid) |
Введите в зацепление 4 захвата.
Установите вещевой ящик в облицовке туннеля пола и закрепите его 4 болтами и 2 винтами.
10. INSTALL CONSOLE BOX CARPET (w/o Console Box Lid) |
Установите коврик вещевого ящика в облицовке туннеля пола.
11. INSTALL CONSOLE BOX CARPET (w/ Console Box Lid) |
Установите коврик вещевого ящика в облицовке туннеля пола.
12. INSTALL LOWER CENTER INSTRUMENT PANEL FINISH PANEL |
Введите в зацепление 4 захвата и 6 фиксаторов.
Установите центральную нижнюю облицовочную накладку панели приборов и закрепите ее 2 винтами <E> или <F>.
13. INSTALL POSITION INDICATOR HOUSING ASSEMBLY |
Введите в зацепление 7 захватов и установите корпус индикатора положения в сборе.
14. INSTALL REAR CONSOLE BOX COVER |
Подсоедините разъем.
Установите крышку вещевого ящика в облицовке туннеля пола и закрепите ее 4 фиксаторами.
15. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY |
Install the shift lever knob sub-assembly.
16. INSTALL INSTRUMENT PANEL FINISH PANEL END LH |
Введите в зацепление 4 фиксатора и установите левую отделочную накладку панели приборов.
17. INSTALL INSTRUMENT PANEL FINISH PANEL END RH |
Введите в зацепление 4 фиксатора и установите правую отделочную накладку панели приборов.
18. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
19. INSPECT SHIFT LEVER POSITION |
When moving the lever from the P position to the R position with the ignition switch on (IG) and the brake pedal depressed, make sure that the shift lever moves smoothly and moves correctly into position.
Start the engine and make sure that the vehicle moves forward when moving the lever from the N position to the D position and moves rearward when moving the lever to the R position. If the operation cannot be performed as specified, inspect the park/neutral position switch assembly and check the shift lever assembly installation condition.
20. ADJUST SHIFT LEVER POSITION |
Apply the parking brake and move the shift lever to the N position.
Remove the lower instrument panel finish panel (See page Нажмите здесь).
Disconnect the end of the transmission control cable assembly from the shift lever assembly.
Turn the lock nut counterclockwise. While holding the lock nut, disconnect the transmission control cable from the shift lever retainer.
Slide the slider of the transmission control cable in the direction indicated by the arrow and pull the lock piece outward.
Connect the outer part of the transmission control cable to the shift lever retainer.
Install the transmission control cable end to the shift lever assembly.
Push the lock piece into the adjuster case.
After adjusting the shift lever position, check that the operation and function of the shift lever. If there is a problem, adjust the position again.
Install the lower instrument panel finish panel (See page Нажмите здесь).